• Integra Tech: [Read and post your basic questions here.]
#101
94 Integra LS Maintenance. There is a slight oil leak in the engine. I think it's due to gasket. It's a tiny oil leak. Is there a way to check it if theres anything wrong?
And i wanna know how to maintain the paint job.
And i wanna know how to maintain the paint job.
#102
I missed Sean
Join Date: Aug 2004
Location: Fairfield/Bridgeport CT
Posts: 11,285
Likes: 0
Received 1 Like
on
1 Post
uh... yeah theres something wrong... you have an oil leak.
as for the paint just wash it by hand using products supported by the guys over at www.autopia.org
as for the paint just wash it by hand using products supported by the guys over at www.autopia.org
#104
I missed Sean
Join Date: Aug 2004
Location: Fairfield/Bridgeport CT
Posts: 11,285
Likes: 0
Received 1 Like
on
1 Post
it really depends on what you want to use for the paint surface...
i choose to hand wash with microfiber mitts, and dry with a microfiber towels.
as for wax i havent really gotten around to it, but there any a full review section on autopia that covers it. i use spray wax every other time i wash to help keep up so far..
really everything for your finish needs is on www.autopia.org
now the oil leak with require a new gasket (if thats infact what you need)
if its a head gaset leak buy a head gasket... its really realitivly simple to figure out what you need it's doing it thats the hard part.
i choose to hand wash with microfiber mitts, and dry with a microfiber towels.
as for wax i havent really gotten around to it, but there any a full review section on autopia that covers it. i use spray wax every other time i wash to help keep up so far..
really everything for your finish needs is on www.autopia.org
now the oil leak with require a new gasket (if thats infact what you need)
if its a head gaset leak buy a head gasket... its really realitivly simple to figure out what you need it's doing it thats the hard part.
#106
Junior Member
Join Date: Mar 2006
Location: panama city, florida
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
hey....im needing some help with replacing my distributor...and also..about a timing light......yeah as you can tell im clueless..so fill me in...ok thanks!!
#107
THESE ARE THE OBD-1 CHECK ENGINE CODES
MIL
MIL
0
Engine Control Module (ECM/ECU) 1
Heated 02 sensor 3
Manifold Absolutre Pressure (MAP Sensor) 4
Crank Shaft Position Sensor (CKP Sensor) 6
Engine Coolant Temperature (ECT Sensor) 7
Throttle Position (TP sensor) 8
Top Dead Center Position (TDC sensor) 9
#1 Cylinder Position (CYP sensor) 10
Intake Air Temperature (IAT sensor) 13
Barometric Sensor (BARO sensor) 14
Idle Air Control Valve (IACV sensor) 15
Ignition Output Signal 16
Fuel Injector 17
Vehicle Speed Sensor (VSS sensor) 19
Lock Solenoid Valve (A/T trans) 20
Electrical Load Sensor (ELD sensor) 21
VTEC Solenoid (VTS) 22
VTEC Pressure Switch (VTPS sensor) 23
Knock Sensor (KS) 30
A/T FI Signal A 31
A/T FI Signal B41
Heated 02 Sensor 43
Fuel Supply
#108
Apathy Kills
Thread Starter
Originally Posted by mrproul
THESE ARE THE OBD-1 CHECK ENGINE CODES...
:cheers: Thank you very much for contributing.. I've added these codes to the Integra FAQ as well, giving you full credit (it's only right.)
Many thanks. :goodjob:
__________________
:: :ToDspin: - supermod - but who gives a shit?
:: HAN Integra FAQ: If, by some miracle, yours hasn't been stolen... check it out!
:: HAN Integra FAQ: If, by some miracle, yours hasn't been stolen... check it out!
#110
how to remove 90 integra headlight
nothing wrong with the headlight, but i just want to clean the inside, look very tuff to remove, after i losing 3 bolts on top of the headlight bracket but it is still very tight, there is any more bolt around. Help me!!!!!!!!!!!!!!!!!