Notices
Engine Swaps, Tech & Tuning Swaps, N/A Performance, Forced Induction, Engine Management, & Troubleshooting

Post Questions about engine swaps.

Thread Tools
 
Old Nov 19, 2003 | 07:38 PM
  #141  
Kai's Avatar
Kai
Rotorphile.
 
Joined: Mar 2002
Posts: 10,120
Likes: 0
From: Richmond, VA
Default

Originally posted by EG8dood
http://www.hondaklubben.com/reportag...ellerasen2.jpg thes r honda civic turbo
Uhh... do you have a question? :eh:
Reply
Old Dec 6, 2003 | 11:46 AM
  #142  
PRojecT....REX's Avatar
PRojecT....REX
Junior Member
 
Joined: Dec 2003
Posts: 4
Likes: 0
From: williamson, west virginia
Default

I dont no much about the engine codes or nothing on honda's but i have an 89 crx-hf, and a 1.6 v-tech engine out of a 94 civic hatch, what will i need for the swap
Reply
Old Dec 12, 2003 | 10:40 PM
  #143  
JunM's Avatar
JunM
Junior Member
 
Joined: Dec 2003
Posts: 16
Likes: 0
Default

say i bring a complete b18a changeover kit from hmotors along with a rolling 86 crx to a shop...will i need those hasport mounts? also, how does the exhaust setup work? will i need a new exhaust?
Reply
Old Dec 13, 2003 | 05:38 AM
  #144  
jaje's Avatar
jaje
HC Racer H5
 
Joined: May 2000
Posts: 4,261
Likes: 0
From: KCK
Default

Originally posted by JunM
say i bring a complete b18a changeover kit from hmotors along with a rolling 86 crx to a shop...will i need those hasport mounts? also, how does the exhaust setup work? will i need a new exhaust?
you will need the mounts and depending on the rolling crx chassis a lot of wiring (si will have efi and will be simpler to wire, where dx and hf had carburetors)...as for the exhaust i'm not too sure but most likely have to have a mid pipe fabricated to fit to the stock exhaust (which i'd replace with a better flowing catback)
Reply
Old Dec 13, 2003 | 11:43 AM
  #145  
lime91crx's Avatar
lime91crx
Registered User
 
Joined: Nov 2003
Posts: 44
Likes: 0
Default

what do i have to do to get a d16a1 into a 91 crx hf. i hooked up my hf transmission to it and the starter wont reach the flywheel. do u think the si transimission will work or what will i have to do about that.
Reply
Old Dec 13, 2003 | 08:11 PM
  #146  
lime91crx's Avatar
lime91crx
Registered User
 
Joined: Nov 2003
Posts: 44
Likes: 0
Default

hi, what would i have to do to get a d16a1 into my 91 crx hf. i triedto put my hf transmission on it but the starter wouldnt reach the flywheel, but i was thinking an si transmission but i wanted to see first.
Reply
Old Jan 7, 2004 | 02:56 PM
  #147  
crxb16er's Avatar
crxb16er
Registered User
 
Joined: Mar 2003
Posts: 1,412
Likes: 0
From: Tucson AZ
Default

try starting a thread on it, you wont get responses as quickly putting that question on here better to put it out in the open for all to respond
Reply
Old Jan 13, 2004 | 12:15 PM
  #148  
AppleSauseSi's Avatar
AppleSauseSi
Critical S.O.B.
 
Joined: Jan 2004
Posts: 186
Likes: 0
From: SFV California
Default

What would be the best, and easiest, swap for a ’91 CRX Si? The engine will need to be ‘91+ and USDM because of California emission laws. Preferably something DOHC, VTEC would be nice too. Also, where could I find this engine, and what all extras will I need? I'm looking to spend no more than 2.5k.
Reply
Old Jan 13, 2004 | 03:01 PM
  #149  
Kai's Avatar
Kai
Rotorphile.
 
Joined: Mar 2002
Posts: 10,120
Likes: 0
From: Richmond, VA
Default

Easiest? D16Z6. Bolts in with minor electronics work.

Best? B18C1. Bolts in like any other B with a few extra wires for the dual stage intake manifold. That's way over $2500 though.
Reply
Old Jan 21, 2004 | 09:21 AM
  #150  
NiteLifeRyder's Avatar
NiteLifeRyder
Registered User
 
Joined: Jan 2004
Posts: 16
Likes: 0
From: Dela-Where?
Default

With all this talk about what will go in a CRX and w/e ppl think up. Exactly how big is the engine bay of the CRX?
Also did ne of u c the 650hp GSR in Hot Compact Import's magazine acouple months ago? Wouldn't that be hot if it were in a CRX?:yes:
Reply



All times are GMT -8. The time now is 11:42 AM.