exhaust, cam, pulley
Thread Starter
Member
Joined: Jun 2002
Posts: 48
Likes: 0
From: So MD
exhaust, cam, pulley
Now, I am decide to buy exhaust, and after reading some feedback I think I am going with Comptech. I also want to get cam and pulley. Any brand or type would anyone suggested?
Thanks.
Thanks.
I
Joined: Jan 2001
Posts: 56,525
Likes: 0
From: Westside til I die
He means AEM cam gears, they only have 3 bolts and like to slip.
__________________
2015 Ford Mustang GT Fastback - Ingot Silver - 6M - Performance Package - Gibson Catback, JLT CAI, FR 47lb injectors, BAMA E85 tune, Eibach Sportline, BMR wheel hop kit, UPR oil separator, Steeda shifter bushing/bracket
Team B.O.B.® - Ballaz on a Budget
2015 Ford Mustang GT Fastback - Ingot Silver - 6M - Performance Package - Gibson Catback, JLT CAI, FR 47lb injectors, BAMA E85 tune, Eibach Sportline, BMR wheel hop kit, UPR oil separator, Steeda shifter bushing/bracket
Team B.O.B.® - Ballaz on a Budget
Thread Starter
Member
Joined: Jun 2002
Posts: 48
Likes: 0
From: So MD
Yeah, I did a search in this forum and no one recomend aem cam, so I lean toward to Jun II, Toda, or Spoon. The problem is I want a good combination with pulley, exhaust. I really like turbo and JRSC but since the car is for commute between work and school only (I put about 110 miles/day) so I think I would stay NA, unless somebody recomend me on the turbo and how to maintaince it. As for time being, should I just get exhaust first.
If I decide to go turbo, I see many recommend to get cam after turbo kit. Money is not going to be that big a deal 'cause I will save up for a while and it's sorta like my project.
Any comment recommendation will be greatly appreciated.
If I decide to go turbo, I see many recommend to get cam after turbo kit. Money is not going to be that big a deal 'cause I will save up for a while and it's sorta like my project.
Any comment recommendation will be greatly appreciated.
Thread Starter
Member
Joined: Jun 2002
Posts: 48
Likes: 0
From: So MD
Oh and one more thing. I know it's important factor on where power band I should aim for. I don't know where should I set my powerband at, but I want a source of power that if I pack 3 passengers in my car (4 people total including me), and when I accelerate, I want them to wet their pants 
THAT's the power that I want. However, I don't want straight out drag though, as I said reliability is very important too.
THAT's the power that I want. However, I don't want straight out drag though, as I said reliability is very important too.
pukimonster
Joined: Jun 2002
Posts: 9,967
Likes: 2
From: Milwaukee, WI
the cams for turbocharged engines are typically short duration and high lift, because you dont want overlap[intake and exhaust valves open at the same time] or else you will force compressed air out of the cylinder. I'd wait on the cams, until you get your turbo on there. And if money isnt an issue, just gimmie $7000 and I'll put the best turbo that money can buy[j/k]. As far as exhaust, I'd get a 2.75" or 3" piping, but that would be extrlemely loud on a n/a car, so i would wait on that till you get a turbo too.
Thread Starter
Member
Joined: Jun 2002
Posts: 48
Likes: 0
From: So MD
Originally posted by brtecson
the cams for turbocharged engines are typically short duration and high lift, because you dont want overlap[intake and exhaust valves open at the same time] or else you will force compressed air out of the cylinder. I'd wait on the cams, until you get your turbo on there. And if money isnt an issue, just gimmie $7000 and I'll put the best turbo that money can buy[j/k]. As far as exhaust, I'd get a 2.75" or 3" piping, but that would be extrlemely loud on a n/a car, so i would wait on that till you get a turbo too.
the cams for turbocharged engines are typically short duration and high lift, because you dont want overlap[intake and exhaust valves open at the same time] or else you will force compressed air out of the cylinder. I'd wait on the cams, until you get your turbo on there. And if money isnt an issue, just gimmie $7000 and I'll put the best turbo that money can buy[j/k]. As far as exhaust, I'd get a 2.75" or 3" piping, but that would be extrlemely loud on a n/a car, so i would wait on that till you get a turbo too.
Geez, $7k huh, well I guess it's expensive to NOT be a ricer
What you mean by best turbo anyway, drag3? Rev hard?
Thread
Thread Starter
Forum
Replies
Last Post
gaydm.accord
Parts Classifieds
6
Sep 1, 2005 10:27 AM
Tr0LL
Engine Swaps, Tech & Tuning
5
Mar 24, 2003 05:26 PM
Tr0LL
Engine Swaps, Tech & Tuning
4
Mar 24, 2003 05:24 PM
jdmcrx22
Parts Classifieds
3
Jan 15, 2003 06:38 AM
