JDM ITR 5 Lug Conversion on 99 Civic SI - HELP
#1
JDM ITR 5 Lug Conversion on 99 Civic SI - HELP
Hey everyone,
I about to get a JDM ITR 5 lug conversion for my 99 Civic SI.
I been told I will run into problems with my SI axles?
I was told that the JDM ITR 5 lug use a 36mm axle, while the USDM ITR and any other B series car uses a 32mm axle?
Can anyone shed some light on this??
I dont want to tear down my car and find out that I'm going to need more parts to get the 5 lug workin on my SI.
Has anyone used a JDM ITR 5 lug conversion before with stock USDM B Series axles?
And if they are different, does anyone know where I can get JDM axles? or should I just go buy the USDM Hubs from acura? I guess all I would have to change would be the front hubs and maybe the bearrings??
Thanks in Advance for the help.
DK
I about to get a JDM ITR 5 lug conversion for my 99 Civic SI.
I been told I will run into problems with my SI axles?
I was told that the JDM ITR 5 lug use a 36mm axle, while the USDM ITR and any other B series car uses a 32mm axle?
Can anyone shed some light on this??
I dont want to tear down my car and find out that I'm going to need more parts to get the 5 lug workin on my SI.
Has anyone used a JDM ITR 5 lug conversion before with stock USDM B Series axles?
And if they are different, does anyone know where I can get JDM axles? or should I just go buy the USDM Hubs from acura? I guess all I would have to change would be the front hubs and maybe the bearrings??
Thanks in Advance for the help.
DK
#2
i'd have to disagree.
i think the jdm itr has the same 32 mm axle nut like the rest of us.
i think the jdm itr has the same 32 mm axle nut like the rest of us.
#4
Maybe the axle nut for some odd is requires a 36 mm socket, but i don't see why it would be a 36 mm axle
hell look at all the jdm itr swap in usdm civic's.
no jdm itr hub's needed...
hell look at all the jdm itr swap in usdm civic's.
no jdm itr hub's needed...
#5
Senior Member
Join Date: Mar 2002
Location: Bay Area, CA
Posts: 196
Likes: 0
Received 0 Likes
on
0 Posts
Well, if you are getting the 5 lug conversion off a jdm integ type R, then you will need the axles from the jdm teg. only the usdm tegs 5 lug will fit with your current si axles. one of my friends who did the conversion ran into this problem.
Just to let you know
Just to let you know
#6
I dont have the JDM Axles.
I think the guy sold them with the SWAP.
Is there any place I can get a set of JDM ITR Axles????
Is it possible to just swap out the HUB, that part the axles goes into with a USDM piece.???
Thanks
DK
I think the guy sold them with the SWAP.
Is there any place I can get a set of JDM ITR Axles????
Is it possible to just swap out the HUB, that part the axles goes into with a USDM piece.???
Thanks
DK
#7
Registered User
Join Date: Jun 2004
Location: Seattle,Washington
Posts: 1
Likes: 0
Received 0 Likes
on
0 Posts
JDM Axles
I Just ran into this Problem now! upon doing some research I discovered that this: USDM 5-lug = 32mm, JDM 5-lug = 36mm, So now I need to go out and find JDM ITR Axles and I have no Idea where to find them please help me out guys! I can't drive my car until I find and Install these!
#8
Registered User
Join Date: Mar 2004
Location: SGV, So Cal
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by MaliceCrew
I Just ran into this Problem now! upon doing some research I discovered that this: USDM 5-lug = 32mm, JDM 5-lug = 36mm, So now I need to go out and find JDM ITR Axles and I have no Idea where to find them please help me out guys! I can't drive my car until I find and Install these!
36mm alxes with nuts and all.
Very rare item.