Honda-Acura.net

Notices
Engine Swaps, Tech & Tuning Swaps, N/A Performance, Forced Induction, Engine Management, & Troubleshooting

Motor swap

 
Old May 9, 2007 | 08:45 PM
Share
  #1  
aka-dk's Avatar
aka-dk
Thread Starter
Caleb
 
Joined: Nov 2006
Posts: 12
Likes: 0
From: Hallettsville
Default Motor swap
Im going to put a '92 integra B18a motor into a 1993 integra. How hard is it to swap? Details please, as in what to take off to do it. Any advice would be appreciated, thanks.
Reply
0
Old May 9, 2007 | 08:57 PM
Share
  #2  
Provocateur's Avatar
Provocateur
On permanent hiatus
 
Joined: Jul 2004
Posts: 9,716
Likes: 0
From: A forum with actual tech
Default
The engine should just be a direct bolt-in replacement.

Moved to Engine Swaps.
Reply
0
Old May 10, 2007 | 04:43 AM
Share
  #3  
aka-dk's Avatar
aka-dk
Thread Starter
Caleb
 
Joined: Nov 2006
Posts: 12
Likes: 0
From: Hallettsville
Default
Will i have to take the tranny from the motor or will i be able to pull it out together?
Reply
0
Old May 10, 2007 | 05:44 AM
Share
  #4  
primetime's Avatar
primetime
Junior Member
 
Joined: Mar 2005
Posts: 322
Likes: 0
From: Connecticut
Default
Originally Posted by aka-dk
Will i have to take the tranny from the motor or will i be able to pull it out together?
Pull it out all together! How many miles on the motor though? if it is a high mileage motor that wasn't maintain very well then you may need to rebuild the bottom end with new rings, bearing, gasket seals, etc. etc.
Reply
0
Old May 10, 2007 | 06:59 AM
Share
  #5  
aka-dk's Avatar
aka-dk
Thread Starter
Caleb
 
Joined: Nov 2006
Posts: 12
Likes: 0
From: Hallettsville
Default
Well my brothers motor in his 93 integra is shot so im put my B18a in it, it has about 95,000mi. on it. It shouldn't be a problem putting it in with the tranny still attached would it?
Reply
0
Old May 10, 2007 | 09:30 AM
Share
  #6  
primetime's Avatar
primetime
Junior Member
 
Joined: Mar 2005
Posts: 322
Likes: 0
From: Connecticut
Default
Originally Posted by aka-dk
Well my brothers motor in his 93 integra is shot so im put my B18a in it, it has about 95,000mi. on it. It shouldn't be a problem putting it in with the tranny still attached would it?
No there should be any clearance issues. it better to drop in the motor and tranny together anyway!
Reply
0
Old May 10, 2007 | 12:12 PM
Share
  #7  
Provocateur's Avatar
Provocateur
On permanent hiatus
 
Joined: Jul 2004
Posts: 9,716
Likes: 0
From: A forum with actual tech
Default
Remove the old one as a complete unit with engine and tranny, remove tranny from motor, put on new motor, and drop in new motor/tranny. It should be that simple.
Reply
0
Old May 11, 2007 | 06:50 AM
Share
  #8  
aka-dk's Avatar
aka-dk
Thread Starter
Caleb
 
Joined: Nov 2006
Posts: 12
Likes: 0
From: Hallettsville
Default
I planned on using my tranny as well. That shouldn't be a problem right? It should mount up the same.
Reply
0
Old May 13, 2007 | 10:10 AM
Share
  #9  
aka-dk's Avatar
aka-dk
Thread Starter
Caleb
 
Joined: Nov 2006
Posts: 12
Likes: 0
From: Hallettsville
Default
Originally Posted by aka-dk
I planned on using my tranny as well. That shouldn't be a problem right? It should mount up the same.
Anyone???
Reply
0
Old May 14, 2007 | 04:53 AM
Share
  #10  
primetime's Avatar
primetime
Junior Member
 
Joined: Mar 2005
Posts: 322
Likes: 0
From: Connecticut
Default
Originally Posted by aka-dk
Anyone???
everything will drop in!
Reply
0

Thread Tools

Advanced Search
Reply Closed Thread Share
Forum Jump

All times are GMT -8. The time now is 06:01 AM.