Any Difference between B18C5 n B18C?
#1
Junior Member
Thread Starter
Join Date: Nov 2006
Location: Singapore
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Any Difference between B18C5 n B18C?
Hi guys, i'm petty new to swapping engine so need alot of advise from u guys..
Currently i swapping my B16A4 to B18C.
My question is the b18C5 block,crankshaft, piston n rod same as B18C?
I know the different between B18C5 n B18C is the camshaft, vavle n valve springs is difference so i decided to buy all the type R parts to add on..
Currently i swapping my B16A4 to B18C.
My question is the b18C5 block,crankshaft, piston n rod same as B18C?
I know the different between B18C5 n B18C is the camshaft, vavle n valve springs is difference so i decided to buy all the type R parts to add on..
#2
Junior Member
Join Date: Mar 2005
Location: Connecticut
Posts: 322
Likes: 0
Received 0 Likes
on
0 Posts
Hi guys, i'm petty new to swapping engine so need alot of advise from u guys..
Currently i swapping my B16A4 to B18C.
My question is the b18C5 block,crankshaft, piston n rod same as B18C?
I know the different between B18C5 n B18C is the camshaft, vavle n valve springs is difference so i decided to buy all the type R parts to add on..
Currently i swapping my B16A4 to B18C.
My question is the b18C5 block,crankshaft, piston n rod same as B18C?
I know the different between B18C5 n B18C is the camshaft, vavle n valve springs is difference so i decided to buy all the type R parts to add on..
#3
Junior Member
Thread Starter
Join Date: Nov 2006
Location: Singapore
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
Cos i thot C5 block is stronger n meant for holding high rev dan B18C
#4
been there done that
like i said in your other thread, the c5 crank is heaver so it can withstand the higher revs. as well as having dual springs on the intake and exhaust sides of the head and lighter intake valves.
#5
Still here... sorta...
A JDM B18C can be either a Type-R engine or a SiR-G (GSR) engine. Therefore, I don't think your comparison makes much sense unless we're actually talking about an SiR-G B18C. :shrug:
#7
been there done that
#8
Junior Member
Thread Starter
Join Date: Nov 2006
Location: Singapore
Posts: 23
Likes: 0
Received 0 Likes
on
0 Posts
c5 and c1 oil pumps have the same part numbers. so i dont see how a c5 pump can flow any more.
like i said in your other thread, the c5 crank is heaver so it can withstand the higher revs. as well as having dual springs on the intake and exhaust sides of the head and lighter intake valves.
like i said in your other thread, the c5 crank is heaver so it can withstand the higher revs. as well as having dual springs on the intake and exhaust sides of the head and lighter intake valves.
Thanks pal..
Guess i will keep driving with my GSR setup b4 starting to change the piston n cam ya...
#9
there is alot of difference between the 2 engines.. as you already know one of them is a gsr and the other is a type r.. we'll start with the basic's the type r has a different cast head based off the b16 head with better valvetrain, valves, cams, and very mild hand port job from the factory, the type r bottom end has some mods done to the crank to hold revs better, the pistons are coated and yield more compression, the rods are stronger and ment for the high revs, the throttle body is bigger, intake manifold matchs the throttle body, the type r has a stock lsd transmission, the gear ratio on type r's are very short and good for track/all motor so it can redline quicker and get through the gears.. the water and oil pump is the same as the type r im pretty sure correct me if im wrong, gsr redline is 8200, type r is 9000, if you have the money for a type r i would get one.. if now just get a gsr build the bottom end, get a b16 head build that up, and get a b16 tranny with a type r lsd.. and make a better engine then the type r with all aftermarket parts .. ive seen poor mans type r's run 12's all day all motor
#10
i recently bought a civic si 99 with a b18c1 swap, and i dont know what to put on the engine to be faster, i want to tune up all the car and i mean all the car, teh car came with headers dc and im not sure what buy first, an intake or an exhaust system and what brand would be better, of teh intake i thought about a aem v2 and the exhaust a tanabe concept g, if anyone could give me an advice please