260 wheel horse power all motor
Thread Starter
Senior Member
Joined: Dec 2002
Posts: 108
Likes: 0
260 wheel horse power all motor
My set up as of 12/03/05:
Car: 1990 Accord 4 door Lx
Engine Block: '93 H22a "bored and stroked" to 2.44ltrs of displacement built by Collective Racing. Custom 98mm Crank, 89mm Darton sleeves, Crower Pro-billet rods, 12/1 compression 89mm JE pistons, Prodrive oil pump, ATR crank pulley, manual timing belt tensioner conversion, ARP main studs.
Cylinder head: Portwork by Collective Racing, Web Cams camshafts (89/267), Web Cams springs and Titainium retainers, ITR LMAs, 50mm TWM ITBs, Hondata intake manifold gasket, RC engineering 440cc Fuel injectors, STR cam seal, STR cam gears, RMF 4-1 header, ARP head studs, Cometic head gasket.
Transmission: T2T4, prodrive 4.7 FD, carbon synchros
Misc: NGK wires, NepTune engine management, 2 1/2" crunch bent exaust
I did a cylinder leakage test on 12/02/05 which was 3% across the board. Compression test was 240Psi +/- 5psi across the board. This engine to date has (still, due to lack of driving recently) 56K miles on it.
solid line = 2nd RMF header dotted line = first RMF header
I am posting in lieu of recent "controversy" over mods done to my car. I have remained silent about recent events as to let the figures and the actions of individuals involved speak for themselves.
Today at Locash Racing, Joe tested (bolt on only) my new version of a RMF header built for my car. I will only be comparing this new header to the previous RMF header.
This header looks very similiar to the EG race header that Randy has pictured at IPH, however it is fitted to my car. Seat of the pants felt absolutely KILLER!
Randy and I drove the car to Locash racing for a PRELIMINARY TEST. NO FUEL TUNING WAS DONE. The header made more peak HP and peak TQ than his last design. The intake temps were controlled by Joe and he tried to keep them as close to the previous testing temps as possible. I believe todays intake temps were slightly higher than before. Also, the A/F was really rich.
This header peaked out at 260hp and 201tq (open header). The header is not 100% finished and this test was only to serve as "data gathering" for Randy. A few changes are to be made and at that point the header will then be tuned with a full exaust.
I will post more information as soon as I recieve it from Locash.
I want to thank Randy for his help on this project and Joe Sawyer for the use of his tuning facility. :thumbup:
Car: 1990 Accord 4 door Lx
Engine Block: '93 H22a "bored and stroked" to 2.44ltrs of displacement built by Collective Racing. Custom 98mm Crank, 89mm Darton sleeves, Crower Pro-billet rods, 12/1 compression 89mm JE pistons, Prodrive oil pump, ATR crank pulley, manual timing belt tensioner conversion, ARP main studs.
Cylinder head: Portwork by Collective Racing, Web Cams camshafts (89/267), Web Cams springs and Titainium retainers, ITR LMAs, 50mm TWM ITBs, Hondata intake manifold gasket, RC engineering 440cc Fuel injectors, STR cam seal, STR cam gears, RMF 4-1 header, ARP head studs, Cometic head gasket.
Transmission: T2T4, prodrive 4.7 FD, carbon synchros
Misc: NGK wires, NepTune engine management, 2 1/2" crunch bent exaust
I did a cylinder leakage test on 12/02/05 which was 3% across the board. Compression test was 240Psi +/- 5psi across the board. This engine to date has (still, due to lack of driving recently) 56K miles on it.
solid line = 2nd RMF header dotted line = first RMF header
I am posting in lieu of recent "controversy" over mods done to my car. I have remained silent about recent events as to let the figures and the actions of individuals involved speak for themselves.
Today at Locash Racing, Joe tested (bolt on only) my new version of a RMF header built for my car. I will only be comparing this new header to the previous RMF header.
This header looks very similiar to the EG race header that Randy has pictured at IPH, however it is fitted to my car. Seat of the pants felt absolutely KILLER!
Randy and I drove the car to Locash racing for a PRELIMINARY TEST. NO FUEL TUNING WAS DONE. The header made more peak HP and peak TQ than his last design. The intake temps were controlled by Joe and he tried to keep them as close to the previous testing temps as possible. I believe todays intake temps were slightly higher than before. Also, the A/F was really rich.
This header peaked out at 260hp and 201tq (open header). The header is not 100% finished and this test was only to serve as "data gathering" for Randy. A few changes are to be made and at that point the header will then be tuned with a full exaust.
I will post more information as soon as I recieve it from Locash.
I want to thank Randy for his help on this project and Joe Sawyer for the use of his tuning facility. :thumbup:
Thread Starter
Senior Member
Joined: Dec 2002
Posts: 108
Likes: 0
Why? Damn... haters everywhere here. 
I post my Accord in the Accord section and I get "hated" on because it has an h22 in it. I post in the Prelude section and I get "hated" on because my h22 has an Accord around it.
The only thing out of place with my post is the fact I said this engine is in an Accord. The post is about the engine and the H22 comes out of the Prelude but maybe you didn't relize that...
Do you honestly think the Accord forum is geard more towards engine performance than the Prelude section? I get tired of talking about body kit this and neon that... catch my drift?
I post my Accord in the Accord section and I get "hated" on because it has an h22 in it. I post in the Prelude section and I get "hated" on because my h22 has an Accord around it.The only thing out of place with my post is the fact I said this engine is in an Accord. The post is about the engine and the H22 comes out of the Prelude but maybe you didn't relize that...
Do you honestly think the Accord forum is geard more towards engine performance than the Prelude section? I get tired of talking about body kit this and neon that... catch my drift?
You Big Dummy
Joined: Jun 2004
Posts: 964
Likes: 0
From: Northwest Florida
Originally Posted by Draconius
why are you posting an accord in the prelude forum?
Great numbers, now lets see what that DC loving "splatch"(or whatever that guy in the Accord forums name was) and others have to say about you and your RMF header. Keep up the good work.
bad as hatch
Joined: Nov 2005
Posts: 47
Likes: 0
From: ontario canada
Originally Posted by 2legit2quit
The post isn't about his car, it's about the H22 powering it.
Great numbers, now lets see what that DC loving "splatch"(or whatever that guy in the Accord forums name was) and others have to say about you and your RMF header. Keep up the good work.
Great numbers, now lets see what that DC loving "splatch"(or whatever that guy in the Accord forums name was) and others have to say about you and your RMF header. Keep up the good work.
i agree you have a nice set up and make good power but cmon be more helpful than bragging. I will get off you back. good luck I hope it REALLY works for you and this is not a way to make yourself look good in our eyes. to some you do already, but more bragging make you look bad. I hope you understand
peace
You Big Dummy
Joined: Jun 2004
Posts: 964
Likes: 0
From: Northwest Florida
Originally Posted by Splatch
did a search on my name to find you talking your shit. here is what I have to say ITOLD YOU SO AND YOU CLAIMED TO BE BILLY BADASS. if you were more helpful posting FACTS instead of about your GODLINESS people would respect yu more.
A Philanthropical Fruit
Joined: Sep 2004
Posts: 756
Likes: 0
From: Ann Arbor Michigan Aim: nickbeier
Originally Posted by Splatch
did a search on my name to find you talking your shit. here is what I have to say ITOLD YOU SO AND YOU CLAIMED TO BE BILLY BADASS. if you were more helpful posting FACTS instead of about your GODLINESS people would respect yu more.
i agree you have a nice set up and make good power but cmon be more helpful than bragging. I will get off you back. good luck I hope it REALLY works for you and this is not a way to make yourself look good in our eyes. to some you do already, but more bragging make you look bad. I hope you understand
peace
i agree you have a nice set up and make good power but cmon be more helpful than bragging. I will get off you back. good luck I hope it REALLY works for you and this is not a way to make yourself look good in our eyes. to some you do already, but more bragging make you look bad. I hope you understand
peace
