Notices

Round shift knobs in teggy

Thread Tools
 
Old Oct 28, 2003 | 07:09 AM
  #21  
BonzoAPD's Avatar
BonzoAPD
Thread Starter
Senior Member
 
Joined: Mar 2002
Posts: 16,353
Likes: 0
From: Ossining, New York
Default

Originally posted by Xymox007

MOMO Race Air Leather.
where can I find one of these?
Reply
Old Oct 28, 2003 | 07:14 AM
  #22  
Xymox007's Avatar
Xymox007
Björkian
 
Joined: Jul 2003
Posts: 722
Likes: 0
From: Pennsylvania
Default

Originally posted by BonzoAPD
where can I find one of these?
Bonzo,

You can find them anywhere on the internet. Just shop around before you buy. I've seen them sell (brand new) for as low as $30.00.

Type in "MOMO Race Air Leather" into www.google.com .
Reply
Old Oct 28, 2003 | 08:29 AM
  #23  
Skelly_GSR's Avatar
Skelly_GSR
RB does men
 
Joined: Jan 2003
Posts: 11,997
Likes: 0
From: Pittsburgh
Default

Originally posted by 98grnLS.
. its the dealers fault for leaving a car like that unlocked.
:down: to you
Reply
Old Oct 28, 2003 | 08:49 AM
  #24  
AXiS's Avatar
AXiS
Member
 
Joined: Jun 2002
Posts: 74
Likes: 0
From: Florida
Default

Bah, that's what they have insurance for. It's not like they can't just get another 10 dollar knob at cost and put it back into the car.. and also I've never seen a dealership leave a car unlocked after hours, that's just stupid. It WAS after hours, right?
Reply
Old Oct 28, 2003 | 08:52 AM
  #25  
LT's Avatar
LT
The deer had to die!
 
Joined: Jun 2002
Posts: 39,835
Likes: 0
From: Fussa, Japan
Default

SKUNK2!!!

Reply
Old Oct 28, 2003 | 09:44 PM
  #26  
CiViC2nR86's Avatar
CiViC2nR86
JDM Padawin
 
Joined: Jul 2003
Posts: 545
Likes: 0
From: Mesa, Arizona
Default

I got some shift knob today and it doesnt twist on like the stock ones. The bottom ring thing has 3 little holes in it. i dont know what to do guys. Does anyone have one of these?
Reply
Old Oct 28, 2003 | 10:08 PM
  #27  
Kai's Avatar
Kai
Rotorphile.
 
Joined: Mar 2002
Posts: 10,120
Likes: 0
From: Richmond, VA
Default

Those three holes are probably tapped. You need some set screws to attach it.
Reply
Old Oct 28, 2003 | 11:42 PM
  #28  
aznd000d's Avatar
aznd000d
yoooooooooooo
 
Joined: Oct 2003
Posts: 148
Likes: 0
From: Riverside, CA
Default

Originally posted by CiViC2nR86
I got some shift knob today and it doesnt twist on like the stock ones. The bottom ring thing has 3 little holes in it. i dont know what to do guys. Does anyone have one of these?

dude, from my experience, I suggest that you don't put those on. they come loose after a few days, and they put bite marks on your shifter. It's a b!tch when it comes up while i'm driving, I then gotta pull over, find the damn key to tighten the knob again.

Here's what I have on my car now.

Reply
Old Oct 28, 2003 | 11:45 PM
  #29  
Kai's Avatar
Kai
Rotorphile.
 
Joined: Mar 2002
Posts: 10,120
Likes: 0
From: Richmond, VA
Default

If you dimple the shifter and use some locktite, it isn't going anywhere.

Then again, it would be on there forever if you did that, short of cutting it off.
Reply
Old Oct 28, 2003 | 11:49 PM
  #30  
aznd000d's Avatar
aznd000d
yoooooooooooo
 
Joined: Oct 2003
Posts: 148
Likes: 0
From: Riverside, CA
Default

when I screwed it on tight, it put dimples on my shifter, but I dind't use locktite. I'm afraid that with all those dimples around the shifter, it's going to be easy for the shifter to snap when shifting hard.
Reply



All times are GMT -8. The time now is 12:25 PM.