Notices
Do It Yourself This is where you will find step by step instructions so you can Do it Yourself!

I want to give my head a bath

Thread Tools
 
Old Nov 8, 2004 | 11:32 AM
  #11  
lkailburn's Avatar
lkailburn
Thread Starter
college kid
 
Joined: Mar 2003
Posts: 2,000
Likes: 0
From: New York
Default

hmm, castrol super clean. i'll have to go check that out.

if its inexpensive i will just get it dipped but i really prefer doing everything myself.
Reply
Old Nov 8, 2004 | 05:00 PM
  #12  
raiden571's Avatar
raiden571
turning u inside out
 
Joined: Oct 2003
Posts: 2,545
Likes: 0
From: cortland, ohio
Default

dish washer?
Reply
Old Nov 9, 2004 | 12:50 PM
  #13  
lkailburn's Avatar
lkailburn
Thread Starter
college kid
 
Joined: Mar 2003
Posts: 2,000
Likes: 0
From: New York
Default

haha. hmm never thought about the dishwasher. damn idk.

would the soap have any adverse effects on it? i could run it without any soap or maybe just a small dab or somethin..

hm
Reply
Old Nov 10, 2004 | 06:42 AM
  #14  
noahrexion's Avatar
noahrexion
Registered User
 
Joined: Nov 2004
Posts: 16
Likes: 0
From: AZ
Default

Don worry about the carbon buildup in teh exhaust housing... is it thick with buildup or just black? cause if its just like stained then just leave it alone, cause after 100 miles it will look the same anyway. If its all carboned up, then scrub it with a small wire toothbrush. WHen you are done sand it in a couple stages then wash it again and it will look just fine. You should probably replace the valve seals since its off anyway. And if the head has a lot of miles on it, i would also consider regridning the seats.
Reply
Old Nov 10, 2004 | 11:33 AM
  #15  
lkailburn's Avatar
lkailburn
Thread Starter
college kid
 
Joined: Mar 2003
Posts: 2,000
Likes: 0
From: New York
Default

i've got new valve seals, cam seal, valve cover gasket, getting an oem headgasket.

there is actual carbon build up that i'd like to remove. im also considering doing a mild DIY port and polish on the exhaust side as well as the cx mani i'll be using. i hear polishing the intake was not helpful.

i was told the head is from an 00 civic but the previous owner was unaware of the mileage.
but i'll be lapping the valve/seats so i should get a good seal. i did a lil leak test on em before i tore the head apart and the exhaust side was just a tad leaky. intake was fine, but i'll do them all neways.

i hope getting it acid dipped, or atleast cleaning the fawker over and over and over will be enough to remove all the grinding compound!
Reply
Old Nov 14, 2004 | 06:30 PM
  #16  
b12uceHuy's Avatar
b12uceHuy
Jizz Maste12
 
Joined: Jun 2002
Posts: 702
Likes: 0
From: DISNEYLAND!
Default

Simple Green Automotive cleaner works great.
Reply
Old Nov 14, 2004 | 07:59 PM
  #17  
lkailburn's Avatar
lkailburn
Thread Starter
college kid
 
Joined: Mar 2003
Posts: 2,000
Likes: 0
From: New York
Default

^^ and harmful to aluminum!
Reply
Old Nov 15, 2004 | 08:58 PM
  #18  
b12uceHuy's Avatar
b12uceHuy
Jizz Maste12
 
Joined: Jun 2002
Posts: 702
Likes: 0
From: DISNEYLAND!
Default

Hahahaha
Reply
Old Nov 15, 2004 | 09:12 PM
  #19  
Kai's Avatar
Kai
Rotorphile.
 
Joined: Mar 2002
Posts: 10,120
Likes: 0
From: Richmond, VA
Default

Originally Posted by lkailburn
^^ and harmful to aluminum!
A lot of the good cleaners out there, including the Castrol Super Clean that I recommend, will eat aluminum. The trick is to wash it off before it does any damage (it takes quite a while to do any noticable damage.)
Reply
Old Nov 16, 2004 | 08:15 AM
  #20  
lkailburn's Avatar
lkailburn
Thread Starter
college kid
 
Joined: Mar 2003
Posts: 2,000
Likes: 0
From: New York
Default

eh i'd rather minimize the damage done. cuz wether you can see it or not, its still damaging the alum

thnx for the suggestions tho. i do appreciate !
Reply



All times are GMT -8. The time now is 02:21 AM.