Power window install w/ SPAL window kit
#1
DIY: Power window install w/ SPAL window kit
Howdy!
This is my tutorial on how to install power windows in a CRX utilizing the JDM power window switches and the SPAL power window kit.
The diagram attached shows how I did it. You dont necessarily have to do it my way, but this method worked out fine for me.
Here are the items I bought to do this whole project:
- SPAL power window kit
- JDM door panels
- JDM power window switches w/ the wire harness
- Relay w/ 5 pins (not sure what brand, it was free from this audio store)
- Automotive wire from Radio Shack
- Soldering equipment
- Solder iron
- Solder
- Quick disconnect connectors
- Spade terminals connectors
- Heat-shrink tubing
The drivers side was the side I installed first because the power window switch had only 5 wires. Those wires are:
- Blue w/ yellow
- Blue w/ green
- Blue w/ red
- Blue w/ white
- Blue w/ black
Power window wiring (Drivers' side)
Blue w/ yellow = grounded
Blue w/ green = grounded
Blue w/ red was attached to the red wire coming out of the SPAL motor
Blue w/ white was attached to the black wire coming out of the SPAL motor
Blue w/ black was attached to pin #87 in the relay
Relay wiring
Now for the relay wiring portion:
#85 = grounded
#30 runs straight to the battery
#87 gets attached to the blue w/ black wire (drivers' side) and the white w/ yellow wire (pass. side). So you have to split the wire coming out of the relay to go into those two wires.
#86 goes into the #3 fuse slot in the fues box. The reason why this was done is so that the windows can only be opened when there's a key in the ignition.
Power window wiring (Passengers' side)
Red w/ yellow was attached to the black wire coming out of the SPAL motor
Red w/ blue was attached to the red wire coming out of the SPAL motor
White w/ yellow gets attached to #87 out of the relay
Black = ground
The JDM master power window switch is on my passenger side and it has the ability to control the other window but I chose not to do that. I just want the windows to go down.
Props go out to Louie B. from the CRX Owners Club for all the help.
Sticky this if you'd like. Thanks
This is my tutorial on how to install power windows in a CRX utilizing the JDM power window switches and the SPAL power window kit.
The diagram attached shows how I did it. You dont necessarily have to do it my way, but this method worked out fine for me.
Here are the items I bought to do this whole project:
- SPAL power window kit
- JDM door panels
- JDM power window switches w/ the wire harness
- Relay w/ 5 pins (not sure what brand, it was free from this audio store)
- Automotive wire from Radio Shack
- Soldering equipment
- Solder iron
- Solder
- Quick disconnect connectors
- Spade terminals connectors
- Heat-shrink tubing
The drivers side was the side I installed first because the power window switch had only 5 wires. Those wires are:
- Blue w/ yellow
- Blue w/ green
- Blue w/ red
- Blue w/ white
- Blue w/ black
Power window wiring (Drivers' side)
Blue w/ yellow = grounded
Blue w/ green = grounded
Blue w/ red was attached to the red wire coming out of the SPAL motor
Blue w/ white was attached to the black wire coming out of the SPAL motor
Blue w/ black was attached to pin #87 in the relay
Relay wiring
Now for the relay wiring portion:
#85 = grounded
#30 runs straight to the battery
#87 gets attached to the blue w/ black wire (drivers' side) and the white w/ yellow wire (pass. side). So you have to split the wire coming out of the relay to go into those two wires.
#86 goes into the #3 fuse slot in the fues box. The reason why this was done is so that the windows can only be opened when there's a key in the ignition.
Power window wiring (Passengers' side)
Red w/ yellow was attached to the black wire coming out of the SPAL motor
Red w/ blue was attached to the red wire coming out of the SPAL motor
White w/ yellow gets attached to #87 out of the relay
Black = ground
The JDM master power window switch is on my passenger side and it has the ability to control the other window but I chose not to do that. I just want the windows to go down.
Props go out to Louie B. from the CRX Owners Club for all the help.
Sticky this if you'd like. Thanks