need help/opinions with system
07-04-2002, 03:56 PM
#1
yeah it's an automatic
Thread Starter
Join Date: Jun 2002
Location: augusta, ga
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
need help/opinions with system
i am in desperate need of feedback on my crappy system. the 10's i have dont bump as hard as i want them to (they hardly bump more than a single 10), i've been blowing fuses left and right lately, and it just overall sucks. please give me hints on fixing this crappy system 
i am getting my new head unit tomorrow so just tell me if i need to get better wires/box/amp or whatever here's the link, just click the system folder
http://photos.yahoo.com/bc/red97accordse/lst?.dir=/
i am getting my new head unit tomorrow so just tell me if i need to get better wires/box/amp or whatever here's the link, just click the system folder http://photos.yahoo.com/bc/red97accordse/lst?.dir=/
07-04-2002, 06:03 PM
#2
Join Date: Jun 2001
Location: oakland, ca
Posts: 58,578
Likes: 0
Received 0 Likes
on
0 Posts
first... i would wire the subs differently...but dont do this till you post more detailed specs of the components.
that is a 2ch amp. i think youll be better off by wiring that sub in parallel, then bridging the amp.
wire the sub like this:
there are 2 voice coils on that sub. wire the + with the other +, do the same for the -. then take one + and one - from the sub and bridge it to the amp. the writing on the amp tells you how.
but post specs of the amp first.
and your wiring is really messy. clean it up. =)
that is a 2ch amp. i think youll be better off by wiring that sub in parallel, then bridging the amp.
wire the sub like this:
there are 2 voice coils on that sub. wire the + with the other +, do the same for the -. then take one + and one - from the sub and bridge it to the amp. the writing on the amp tells you how.
but post specs of the amp first.
and your wiring is really messy. clean it up. =)
__________________
.
.
07-04-2002, 06:12 PM
#4
yeah it's an automatic
Thread Starter
Join Date: Jun 2002
Location: augusta, ga
Posts: 21
Likes: 0
Received 0 Likes
on
0 Posts
hey here are the specs for the Jensen AMP:
Number of Channels 2
RMS Power Per Channel @ 4 ohm 125x2
RMS Power Per Channel @ 2 ohm 175x2
RMS Power Bridged @ 4 ohm 350x1
Number of Channels 2
RMS Power Per Channel @ 4 ohm 125x2
RMS Power Per Channel @ 2 ohm 175x2
RMS Power Bridged @ 4 ohm 350x1
07-04-2002, 06:52 PM
#10
Join Date: Jun 2001
Location: oakland, ca
Posts: 58,578
Likes: 0
Received 0 Likes
on
0 Posts
a new box will cost $30 plus your labor...if you already have the tools, which any man would. are you a man? =P
.75" MDF
bag of drywall screws
caulk
something to cut straight lines in the wood- table or circular saw
something to cut the speaker hole- jigsaw
something to put the wood together-drill
specs for box- www.rockfordfosgate.com
specs for the size of box- your math skills.
.75" MDF
bag of drywall screws
caulk
something to cut straight lines in the wood- table or circular saw
something to cut the speaker hole- jigsaw
something to put the wood together-drill
specs for box- www.rockfordfosgate.com
specs for the size of box- your math skills.
__________________
.
.
Thread
Thread Starter
Forum
Replies
Last Post
timmyh
Integra & 97-01 Integra Type-R
2
11-06-2003 12:13 PM