Bushing install pics
#1
Bushing install pics
To follow up on Bumnah's report. I took some pics of the lower control arm bushing install. I haven't done the front yet, so if this sparks interest, I may do the same with the front bushings.
Here's the tools I used:
Reciprocating saw
Flathead screwdriver
4" 3 jaw press (harbor freight $6) :thumbup:
Makita drill and 7/64 drill bit
4 lb. hammer.
Drill numerous holes around the bushing. The goal is to weaken the rubber to press it out with the jaw press.
This press is the shizzle! It saved my ass. Just yard on that thing and it should rip the center out.
Like so...
Cut through the bushing, through the sleeve. But be careful not to go through the lca.
Now that you have that out. Just lube up the new bushings and slap them in there.
ENJOY! :thumbup:
Update: Damn red x's will be the death of me!
Here's a link to the album until I get time to fix it.
http://photos.yahoo.com/sntnmjones@sbcglobal.net
Here's the tools I used:
Reciprocating saw
Flathead screwdriver
4" 3 jaw press (harbor freight $6) :thumbup:
Makita drill and 7/64 drill bit
4 lb. hammer.
Drill numerous holes around the bushing. The goal is to weaken the rubber to press it out with the jaw press.
This press is the shizzle! It saved my ass. Just yard on that thing and it should rip the center out.
Like so...
Cut through the bushing, through the sleeve. But be careful not to go through the lca.
Now that you have that out. Just lube up the new bushings and slap them in there.
ENJOY! :thumbup:
Update: Damn red x's will be the death of me!
Here's a link to the album until I get time to fix it.
http://photos.yahoo.com/sntnmjones@sbcglobal.net
#2
Senior Member
Join Date: Mar 2002
Location: Bay Area, CA
Posts: 196
Likes: 0
Received 0 Likes
on
0 Posts
very nice Troy...
Did about the same thing that you did, except that instead of using a drill and the 3-pt jaw press, I just used a 1 1/4" hole saw.
Must of been real easy though with the reciprocating saw. I had to do mine by hand
Did about the same thing that you did, except that instead of using a drill and the 3-pt jaw press, I just used a 1 1/4" hole saw.
Must of been real easy though with the reciprocating saw. I had to do mine by hand
#3
You'll have to go to the album until tomorrow. Hopefully by then I'll have time to fix it.
http://photos.yahoo.com/sntnmjones@sbcglobal.net
http://photos.yahoo.com/sntnmjones@sbcglobal.net
#4
dude, you want me to host the pictures for you?
those bushings are worth it.
i just replaced my rear mount of my motor with the HASport billet drag mount. talk about a bitch and a half!
those bushings are worth it.
i just replaced my rear mount of my motor with the HASport billet drag mount. talk about a bitch and a half!
#5
Originally posted by Bumnah
dude, you want me to host the pictures for you?
those bushings are worth it.
i just replaced my rear mount of my motor with the HASport billet drag mount. talk about a bitch and a half!
dude, you want me to host the pictures for you?
those bushings are worth it.
i just replaced my rear mount of my motor with the HASport billet drag mount. talk about a bitch and a half!
#6
Originally posted by Bumnah
dude, you want me to host the pictures for you?
those bushings are worth it.
i just replaced my rear mount of my motor with the HASport billet drag mount. talk about a bitch and a half!
dude, you want me to host the pictures for you?
those bushings are worth it.
i just replaced my rear mount of my motor with the HASport billet drag mount. talk about a bitch and a half!
How can you host them? Let me know. I can't get these things to come up! SBC DSL hosting sucks the donkey. :madfawk: