Oil Cooler?
#1
Senior Member
Thread Starter
Join Date: Aug 2006
Location: MO
Posts: 387
Likes: 0
Received 0 Likes
on
0 Posts
Oil Cooler?
I have a 99 GS-R that I have done some major mods too. I was looking into adding an oil cooler and after researching I have noticed that my car should have been equipped with one from the factory. Anyone know if this is true of all GS-Rs or just an option on them.
#2
Apathy Kills
If you're concerned about oil temps, I would look into buying a sandwich adapter, AN hoses and an external cooling radiator.
Call me a skeptical bastard, but I distrust oil-to-water cooling setups after seeing the aftermath of one leaking internally. It wasn't on a Honda motor, but main bearing failure and a blown head gasket were just the start of the problems.
__________________
:: :ToDspin: - supermod - but who gives a shit?
:: HAN Integra FAQ: If, by some miracle, yours hasn't been stolen... check it out!
:: HAN Integra FAQ: If, by some miracle, yours hasn't been stolen... check it out!
#3
Moderator
do u have an oil temp and oil pressure gauge setup?
what major mods do you have, and what kind of driving is this car is exposed to?
what major mods do you have, and what kind of driving is this car is exposed to?
__________________
DB Squad
Integra Forum Moderator
2016 BMW 340i M-Sport / 2013 Chevrolet Volt / 1999 Subaru Impreza RS EJ205
DB Squad
Integra Forum Moderator
2016 BMW 340i M-Sport / 2013 Chevrolet Volt / 1999 Subaru Impreza RS EJ205
#5
Senior Member
Thread Starter
Join Date: Aug 2006
Location: MO
Posts: 387
Likes: 0
Received 0 Likes
on
0 Posts
Yea, the idea of an oil to water cooler doesnt sound good to me either. Glad it doesn't have it so it's that much easier to install an oil to air cooler. I do have an oil temp and pressure gauge set installed. On a day at the track, oil temps reach close to 260, which is why I was looking into a cooler. The car sees mostly track time and I'm pretty hard on it, but that's why I built it.
The mods are:
Dart B18 block bored and stroked to 2.2
Crower billet steel crank
Crower stage 3 cams
Crower rods
Crower valvetrain (SS valves, springs, rets)
Crower 12:5 cr pistons
Toga high volume oil pump
PnP head
Edelbrock IM bored to match oversized TB
Warlboro FP
Bored out fuelrail w/modified regulator
RC 440 Injectors
Custom header
Greddy Evo2 exhaust
Fluidyne radiator
Custom tune
The mods are:
Dart B18 block bored and stroked to 2.2
Crower billet steel crank
Crower stage 3 cams
Crower rods
Crower valvetrain (SS valves, springs, rets)
Crower 12:5 cr pistons
Toga high volume oil pump
PnP head
Edelbrock IM bored to match oversized TB
Warlboro FP
Bored out fuelrail w/modified regulator
RC 440 Injectors
Custom header
Greddy Evo2 exhaust
Fluidyne radiator
Custom tune
#6
Moderator
wow, thats a healthy list of mods.
good to see an integra owner doing track days.
260 is pretty high, so get that oil/air cooler in there.
dont know any places off the top of my head where one can easily mount.
good to see an integra owner doing track days.
260 is pretty high, so get that oil/air cooler in there.
dont know any places off the top of my head where one can easily mount.
__________________
DB Squad
Integra Forum Moderator
2016 BMW 340i M-Sport / 2013 Chevrolet Volt / 1999 Subaru Impreza RS EJ205
DB Squad
Integra Forum Moderator
2016 BMW 340i M-Sport / 2013 Chevrolet Volt / 1999 Subaru Impreza RS EJ205