DIY Pedal Assmebly Removal
#1
Senior Member
Thread Starter
Join Date: Dec 2003
Location: Toronto Ontario Canada
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
DIY Pedal Assmebly Removal
If anyone has or knows where to find DIY instructions,or any instructions on how to remove the pedal assembly out of a 90 civic DX 5 speed, could you please post them up or Pm me. I have been looking everywhere but I can't find anything, Thanks.
#4
89 CRX si, now with b16!
Join Date: Mar 2005
Location: Las Vegas, NV
Posts: 456
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Jigga JJ
Im trying to replace the whole pedal assembly.
U have to go under the dash, good luck fitting in there!
1. U have to first remove your throttle cable and clutch cable, on the pedal side. It's best to loosen up the cables in the engine first(or just remove the clutch cable, then remove the throttle cable). To remove the clutch cable, u have to get your hand in there and slide it off the top of the pedal. If u can't reach it, use a screwdriver. Then remove the throttle cable by pulling the cable, then slide the plastic clip off the pedal, and slip the cable out of the pedal through the little hole there.
2. Look at the bracket itself, there should be about 6-7 nuts that u can see holding the bracket to the firewall, and 1 bolt that's holding the bracket up above, by the steering wheel(a little to the right of the fusebox, just locate the pedal bracket there, and you'll see a bolt). Remove the nuts that are holding the bracket in place. You're gonna need an extension and a deep socket to get some of those nuts off, but just keep trying and they'll come off.
3. Remove the cotter pin and bolt that is holding the brake booster to the brake pedal, and also remove the cotter pin and spring from the gas pedal, but remove the ENTIRE gas pedal from the bracket(trust me, it makes this alot easier.
4. Once the bracket is loose, u have to slide the brake booster out from the car, just pull the booster from the engine compartment a little bit until the bolts are visible in the engine are, and not AT ALL in the dash area. Slide the pedal assembly down, and turn it counter clockwise to get it out of there, and VOILA! The pedal assembly should be out now.
Last edited by RevengeCRX; 03-05-2006 at 10:44 PM.
#7
Senior Member
Thread Starter
Join Date: Dec 2003
Location: Toronto Ontario Canada
Posts: 133
Likes: 0
Received 0 Likes
on
0 Posts
Update time
The pedal assembly was finally taken out. That top bolt was a bi**h and a half. It's not even visible untill you remove the duct for the vent on the driverside(dash). I'm just waiting for the new pedal assembly, let's just hope I don't have too hard of a time rembereing where everything goes
Thanks
The pedal assembly was finally taken out. That top bolt was a bi**h and a half. It's not even visible untill you remove the duct for the vent on the driverside(dash). I'm just waiting for the new pedal assembly, let's just hope I don't have too hard of a time rembereing where everything goes
Thanks
#8
89 CRX si, now with b16!
Join Date: Mar 2005
Location: Las Vegas, NV
Posts: 456
Likes: 0
Received 0 Likes
on
0 Posts
Cool. Glad to help.
Oh, sorry I couldn't respond sooner. I forgot to mention that the bolt is right behind that plastic vent tube. My crx didn't have that tube when I removed my pedal assembly, but it's supposed to be there. Glad u got it out okay!
Oh, sorry I couldn't respond sooner. I forgot to mention that the bolt is right behind that plastic vent tube. My crx didn't have that tube when I removed my pedal assembly, but it's supposed to be there. Glad u got it out okay!