Crank pulley bolt: reverse thread?
#12
Originally posted by XSrcing
i use an ingersoll rand 3/4" impact. takes 2 seconds.
i use an ingersoll rand 3/4" impact. takes 2 seconds.
#13
Hi guys. I know this thread is old but just in case. I have a Accord 2.0iS (UK) sounds similar to the 2.0.EX USA. I tried in vain this weekend to remove the pulley bolt. I was going to buy the pulley attachment tool to hold the crank solid. Costs about £62 $85 us dollars. Reckon the extensions and a length og pipe in my raker bar should do it. Any comments
#14
Registered User
Thread Starter
Join Date: May 2003
Location: Northern Virginia
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mondial
Hi guys. I know this thread is old but just in case. I have a Accord 2.0iS (UK) sounds similar to the 2.0.EX USA. I tried in vain this weekend to remove the pulley bolt. I was going to buy the pulley attachment tool to hold the crank solid. Costs about £62 $85 us dollars. Reckon the extensions and a length og pipe in my raker bar should do it. Any comments
#15
Originally Posted by lingerbw
5ft length of pipe over the end of my breaker bar did the trick for me. Some guys say leave the car in 5th gear and put it on the ground and you don't need the pulley tool. I used the tool, though.
#16
Registered User
Thread Starter
Join Date: May 2003
Location: Northern Virginia
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mondial
I tried it in 5th gear but the breaker bar did not have much movement even though I had the car on ramps. The idea of extending out beyond the car body sounds like a good idea.
#17
Hmmmm.....Didn't work for me. I tried my Aircat Impact wrench with 1000FT LBs in reverse, and the crank pulley holder tool.....no luck. Then I saturated it with PB blaster, several times over and gave it an hour to work.....no luck. Then I got a couple of 10" 1/2"dr extensions, an 18" craftsman breaker bar, and a 6 foot piece of steel pipe and snapped the breaker bar. No luck.
I just bought a Propane torch today, so this weekend I'm going to make that sucker glow, and see if I can twist it off then!
I just bought a Propane torch today, so this weekend I'm going to make that sucker glow, and see if I can twist it off then!
#18
Registered User
Thread Starter
Join Date: May 2003
Location: Northern Virginia
Posts: 410
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by H0ndaJunkie
Hmmmm.....Didn't work for me. I tried my Aircat Impact wrench with 1000FT LBs in reverse, and the crank pulley holder tool.....no luck. Then I saturated it with PB blaster, several times over and gave it an hour to work.....no luck. Then I got a couple of 10" 1/2"dr extensions, an 18" craftsman breaker bar, and a 6 foot piece of steel pipe and snapped the breaker bar. No luck.
I just bought a Propane torch today, so this weekend I'm going to make that sucker glow, and see if I can twist it off then!
I just bought a Propane torch today, so this weekend I'm going to make that sucker glow, and see if I can twist it off then!
#19
Second vote for the impact. I made a tool at work to stop the pulley from spinning so I could get the bolt loose. I grabbed some extensions and a cheater bar and tried to break it loose. I pried so hard that the leverage I was using lifted the front end of the car off the ground!
I don't have the luxury of an air compressor and impact so I made a trip to a local garage to have them bust it loose. $10 and a two second blast with an impact had it off in a jiffy. I just had them tighten it up good enough to get back to my house.
I don't have the luxury of an air compressor and impact so I made a trip to a local garage to have them bust it loose. $10 and a two second blast with an impact had it off in a jiffy. I just had them tighten it up good enough to get back to my house.
#20
I suggest using a torque wrench to put the bolt back on. Sure, you can probably get away with giving the bolt a couple of baps with the impact gun but don't risk breaking the bolt or the end of the crankshaft. Using a torque wrench is simple even if you're a flatrate mechanic.