skunk2 intake manifold
#1
Registered User
Thread Starter
Join Date: Oct 2003
Location: Arizona
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
skunk2 intake manifold
Greetings All
I have a completely stock 00 GSR, and I have purchased the Skunk2 intake manifold for it. Does anyone have experience and/or advice regarding installation of this thing? Particularly the gasket issues. Also any opinions on the actual performance gain from this upgrade would also be welcomed.
Thanks
I have a completely stock 00 GSR, and I have purchased the Skunk2 intake manifold for it. Does anyone have experience and/or advice regarding installation of this thing? Particularly the gasket issues. Also any opinions on the actual performance gain from this upgrade would also be welcomed.
Thanks
#3
Link txhatch was talking about
There must be some serious gains to be found with the skunk2 intake manifold, because I discovered a few dozen topics on the skunk2 intake manifold.
There must be some serious gains to be found with the skunk2 intake manifold, because I discovered a few dozen topics on the skunk2 intake manifold.
#4
I hate 2003 Noobs.
Join Date: Aug 2002
Location: tx
Posts: 5,112
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by Xymox007
Link txhatch was talking about
There must be some serious gains to be found with the skunk2 intake manifold, because I discovered a few dozen topics on the skunk2 intake manifold.
Link txhatch was talking about
There must be some serious gains to be found with the skunk2 intake manifold, because I discovered a few dozen topics on the skunk2 intake manifold.
#6
If you change your P73 IM on your GSR to the Skunk2 IM I would buy a new gasket from Acura. You will also need an ITR intake arm or an ITR CAI/SRI as well since the throttle position is going to be higher. You need to swap everything from your old to the new IM as well, TB, Sensors, etc.
But like Snoopy said, on a stock GSR engine you do not need the Skunk2 IM...only if you are doing some major head work like cams/cam gears.
But like Snoopy said, on a stock GSR engine you do not need the Skunk2 IM...only if you are doing some major head work like cams/cam gears.
#8
Registered User
Thread Starter
Join Date: Oct 2003
Location: Arizona
Posts: 24
Likes: 0
Received 0 Likes
on
0 Posts
skunk2 manifold
Thanks Guys!
I will also attach the comptech icebox/intake setup to it as well. Have you any input on a Hondata insulating gasket? Supposed to increase torque ~4% depending on operating temp.
Regarding the opinion that I shouldn't use it on a stock engine, do you think I made a mistake on this purchase? Should I resell this part, or do you just mean that if I install it, it won't help very much?
Thanks again!
I will also attach the comptech icebox/intake setup to it as well. Have you any input on a Hondata insulating gasket? Supposed to increase torque ~4% depending on operating temp.
Regarding the opinion that I shouldn't use it on a stock engine, do you think I made a mistake on this purchase? Should I resell this part, or do you just mean that if I install it, it won't help very much?
Thanks again!
#9
I'm Cooler than You
Join Date: May 2003
Location: Seattle zzz
Posts: 1,654
Likes: 0
Received 0 Likes
on
0 Posts
Originally posted by blazinxracer
:werd:
:werd:
#10
been there done that
Re: skunk2 manifold
Originally posted by apathy23
Thanks Guys!
I will also attach the comptech icebox/intake setup to it as well. Have you any input on a Hondata insulating gasket? Supposed to increase torque ~4% depending on operating temp.
Regarding the opinion that I shouldn't use it on a stock engine, do you think I made a mistake on this purchase? Should I resell this part, or do you just mean that if I install it, it won't help very much?
Thanks again!
Thanks Guys!
I will also attach the comptech icebox/intake setup to it as well. Have you any input on a Hondata insulating gasket? Supposed to increase torque ~4% depending on operating temp.
Regarding the opinion that I shouldn't use it on a stock engine, do you think I made a mistake on this purchase? Should I resell this part, or do you just mean that if I install it, it won't help very much?
Thanks again!