Will this header [fit] my B17?
#1
Junior Member
Thread Starter
Join Date: Jul 2006
Location: Simi Valley, CA
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
Will this header [fit] my B17?
I saw this Jun header and was wondering if it will fit on my 92 GSR. Also is that a real Jun header or a fake?
http://cgi.ebay.com/ebaymotors/Jun-J...spagenameZWDVW
http://cgi.ebay.com/ebaymotors/Jun-J...spagenameZWDVW
#2
been there done that
that's a megan racing header. you notice in the ad they say "BRAND NEW JDM JUN SPOON FULL T-304 STAINLESS STEEL Racing HEADERS "
it'll bolt to your head, but will more than likely hang lower than a header designed for your engine.
it'll bolt to your head, but will more than likely hang lower than a header designed for your engine.
Last edited by Snoopy; 11-17-2006 at 02:06 PM.
#3
www.ufc.com
Join Date: Sep 2004
Location: Irvine CA
Posts: 2,920
Likes: 0
Received 0 Likes
on
0 Posts
Dude that is not a Jun header, and if it were it would not be 149.95. It will fit your head, but the flange will have to be cut and re-welded since the angle it not right.
#5
Junior Member
Thread Starter
Join Date: Jul 2006
Location: Simi Valley, CA
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
I never seen a real jun header on ebay or anywhere so I didnt really know how much they go for. As for fitment issues do you know if that also goes for the Mugen 4-1 header for B18 and B16?
#6
been there done that
a header for a b16 will hit the oil pan if installed on a b18 and a b18 header will hang low if installed on a b16/b17.
#7
got boost?
Join Date: Jan 2005
Location: somewhere
Posts: 2,346
Likes: 0
Received 0 Likes
on
0 Posts
Cause i know the angel on it is opposite then that of a gsr, basing this on have an 00 civic SI as well.. the cat flang are different.
#8
Junior Member
Thread Starter
Join Date: Jul 2006
Location: Simi Valley, CA
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
I'm thinking to buy this header...
http://cgi.ebay.com/ebaymotors/MUGEN...spagenameZWDVW
unless someone gives more than $600
but there was another one just ended a little bit ago and in the description it said it fits both b18 and b16. Its right here...
http://cgi.ebay.com/ebaymotors/JDM-M...spagenameZWDVW
If I have to cut the flendge to get my cat ot fit on there can I instead just run straight exhaust without a cat so I dont have to cut and reweld the flendge?
http://cgi.ebay.com/ebaymotors/MUGEN...spagenameZWDVW
unless someone gives more than $600
but there was another one just ended a little bit ago and in the description it said it fits both b18 and b16. Its right here...
http://cgi.ebay.com/ebaymotors/JDM-M...spagenameZWDVW
If I have to cut the flendge to get my cat ot fit on there can I instead just run straight exhaust without a cat so I dont have to cut and reweld the flendge?
Last edited by GSRboy; 11-17-2006 at 04:59 PM. Reason: more questions
#9
been there done that
#10
www.ufc.com
Join Date: Sep 2004
Location: Irvine CA
Posts: 2,920
Likes: 0
Received 0 Likes
on
0 Posts