finally done with install...turbo...*pics*
#1
turbo mafia
Thread Starter
Join Date: Mar 2002
Location: no.va.
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
finally done with install...turbo...*pics*
finally install's pretty much done...just have to add a new cat. and a flexpipe to my downpipe...
ok, here's the rundown:
t3/t04e 50 trim, stage 2 wheels, .63 a/r
drag gen 4 cast iron manifold
spearco-core intercooler
tial 35mm wastegate
drag 4 blingbling pipings
blitz dd bov
dsm 450cc injectors with obd1 clip
obd1 resistor box
vafc hack
aeroquip ss braided oil return line with 45degree swivel fittings
2.5 inch drag gen 4 downpipe
goodridge ss braided oil feed line
autometer cobalt series boost, egt, a/f gauges
greddy turbo timer
car was already equipped with:
vafc
2.5 catback (which splits into 2.25 dual) with obx b5 mufflers
aem cai
dc sports 4-2-1 header
neuspeed sports springs
wheels, etc etc
install was a bitch! took about 4 days to get all the parts in...injectors took about a day with clips/resistor box...
later found out that i was leaking oil from oil feed and oil return, so had to take them apart and teflon tape it (drag install manual says not to teflon tape the threads), broke a oil pressure sending unit and had to replace that, etc etc etc...
well, after about 2 weeks of total downtime (didn't have time to take it to shop to get the downpipe welded w/ flange for stock cat. since drag's dp doesn't come flanged), the car does finally run without any oil leaks...
well, i'll let the pics speak for themselves...
before pic:
turbo+wastegate+dumptube+oil feed+manifold:
aeroquip ss braided oil return line:
intercooler to compressor pipe:
turbo in engine bay:
making O in the oilpan:
oilpan close up:
oil return line connected from turbo to oilpan:
another pic of oil return:
ok, here's the rundown:
t3/t04e 50 trim, stage 2 wheels, .63 a/r
drag gen 4 cast iron manifold
spearco-core intercooler
tial 35mm wastegate
drag 4 blingbling pipings
blitz dd bov
dsm 450cc injectors with obd1 clip
obd1 resistor box
vafc hack
aeroquip ss braided oil return line with 45degree swivel fittings
2.5 inch drag gen 4 downpipe
goodridge ss braided oil feed line
autometer cobalt series boost, egt, a/f gauges
greddy turbo timer
car was already equipped with:
vafc
2.5 catback (which splits into 2.25 dual) with obx b5 mufflers
aem cai
dc sports 4-2-1 header
neuspeed sports springs
wheels, etc etc
install was a bitch! took about 4 days to get all the parts in...injectors took about a day with clips/resistor box...
later found out that i was leaking oil from oil feed and oil return, so had to take them apart and teflon tape it (drag install manual says not to teflon tape the threads), broke a oil pressure sending unit and had to replace that, etc etc etc...
well, after about 2 weeks of total downtime (didn't have time to take it to shop to get the downpipe welded w/ flange for stock cat. since drag's dp doesn't come flanged), the car does finally run without any oil leaks...
well, i'll let the pics speak for themselves...
before pic:
turbo+wastegate+dumptube+oil feed+manifold:
aeroquip ss braided oil return line:
intercooler to compressor pipe:
turbo in engine bay:
making O in the oilpan:
oilpan close up:
oil return line connected from turbo to oilpan:
another pic of oil return:
#2
turbo mafia
Thread Starter
Join Date: Mar 2002
Location: no.va.
Posts: 118
Likes: 0
Received 0 Likes
on
0 Posts
some more pics...
this is the oil feed location:
dsm 450cc's and obd1 clips:
resistor box from obd1 hondas:
engine bay about 80% complete. notice the egt, boost gauge wire running all over the place:
intercooler + front bumper (lotz of cutting required):
finished engine bay:
blitz dd bov:
snail:
the car:
damn...i should write up a nice how-to-turbo with pics...
this is the oil feed location:
dsm 450cc's and obd1 clips:
resistor box from obd1 hondas:
engine bay about 80% complete. notice the egt, boost gauge wire running all over the place:
intercooler + front bumper (lotz of cutting required):
finished engine bay:
blitz dd bov:
snail:
the car:
damn...i should write up a nice how-to-turbo with pics...
#8
Senior Member
Join Date: Dec 2002
Location: cali, bay area
Posts: 13,574
Likes: 0
Received 0 Likes
on
0 Posts
looks nice, congrats bro, two quick questions, since i'm a turbo noob, why do u have the oil line from the pan to the turbo? whats it's use? and why do u have an cone intake in the turbo? whats it good for?